6.0mm Galvanised Steel Wire Rope

This 6.0mm Galvanised Steel Wire Rope is used primarily used in lifting, slings or rigging.  It is commonly referred to as ‘working wire’.  Galvanised Wire Rope will not work harden in the same way that Stainless Steel wire will over time. Various lengths are offered – and the longer the length, the greater the discount.  The result is that if you buy a greater length, you lower your cost per metre of the material.

Please use the combinations of the offered lengths to get the total length for which you search.

E.G. – choose a quantity of “8” of the 10M length to select a single length of 80 Metres.

All quantities of Wire Rope are cut and shipped as a single length unless otherwise specifically ordered with a ‘cut to length’ service. (additional charge per length of wire to cut to a measurement, coil, label, and wrap separately – see our services section on this website). Lengths of wire less than 100M are cut and labelled as a coil. Lengths of 150M and above are (generally) delivered on a reel however, small lengths can be put on a drum for a small additional cost (please refer to our Reeling Service).

Our international supplier produces AISI Mill Certified wire rope. In addition, the certificate is available on request. Their long experience of wire and rope manufacturing enables them to design and manufacture wire and rope with optimal balance between high tensile strength, fatigue resistance, abrasion resistance, and structural stability. The added bonus is that they provide a special treatment for bright and smooth surface of wire and cable to deliver a truly top-shelf, long lasting product that will look new for ages…

Wire Structure:

Three common wire strand constructions are:

• 1×19 indicates 19 thin wires twisted together in a silky and therefore smooth finish. Consequently, 19 individual wires twisted together construct a single strand of our premium wire. This is the least flexible wire structure. As a result, it is the easiest to keep clean.
• 7×7 indicates a collection of 49 individual wires grouped as 7 sub-strands of 7 wires each. Consequently, 7 wire bundles twisted together form a single strand. This is more (medium) flexible wire than 1×19. As a result, it is for ‘general purpose’ applications and is most economical because it is commonly available.
• 7×19 indicates a collection of 133 individual wires grouped as 7 sub-strands of 19 wires each. Consequently, 7 wire bundles of 19 wires twisted together form a single strand. This is our most flexible wire for use in rigging or small cranes or winches rather than balustrade construction. Low Cost Wire does not recommend 7×19 wire for balustrade construction.

…In conclusion, the more wires twisted to make a strand, the more flexible is the strand of wire because it deforms/bends without damage.

Application:

• First of all, this wire may be mechanically – fastened or manually or hydraulically swaged.
• Cutting of the wire is best done using Parrot Beak cutters (collapsing trapezoidal design) rather than shears or a grinder.
• Terminal Loops are formed with Mechanical fastening or manual swaging. In addition, terminal loops must use stainless steel thimbles (eyelets) to retain the strength of the wire by distributing the load along the entire length of wire in the terminal loop (available here). Recommended for only 7×7 and 7×19 structures
• Mechanical fastening is done with Wire Rope Grips (Bulldog Grips) Low Cost Wire does not recommend this approach. Industry practice is three per terminal loop for safety purposes. This only suits 7×7 and 7×19 structures.
• Manual swaging is done using Ferrules (or crimps or hand swages) rather than Wire Rope Grips. Nickel Coated Copper is used instead of Aluminum because matching alloys is important. As a result, catastrophic swaging failure will not occur. Aluminium swages WILL cause a dissimilar alloys reaction and as a result corrode the Stainless Steel wire. Low Cost Wire strongly recommends an All-in-1 swaging tool. Recommended for only 7×7 and 7×19 structures
• Hydraulic swaging is done using a hydraulic press either bench mounted or hand held. Hydraulic swaging for architectural purposes may economically use a Hydraulic Swaging Tool while remaining work safe. These tools generate pressure ‘spot’ welds. Low Cost Wire strongly recommends that hydraulic swaging for lifting and marine applications use a bench mounted hydraulic press which can generate pressure ‘seam’ welds. This process is recommended for 1×19, but it works with 7×7 and 7×19 structures as well.

Features & Benefits:

• 2070 Marine Grade
  
• Precision Manufactured
• Factory Wrapped & Sealed
• Cut Lengths -measured, bound, and sealed in plastic
• Available as a coil or a reel. Lengths of 150M and above are (generally) delivered on a reel however, small lengths can be put on a drum for a small additional cost (please refer to our Reeling Service).

Specifications:

• Quality: Marine
• Grade: 2070
• Lay: Right Hand
• Swaging Method: Hydraulic or Manual
• Wire Structure: 7×19, 7×7
• Diameter of Wire: 6.0mm

Additional Information